How To Repair The Plaster And Floor Damaged surface

Some defects occur in the plaster surface after continuous use. This is mainly due to climate change and various chemical compounds in the air.After continuous use, some defects occur in the floor, which need to be corrected. Because if not repaired, the defects increase. Depending on the type of floor, the floor is repaired as follows. How To Repair To Damaged Plaster Surface| Cracks in the plaster surface |The plaster peeling off |Plaster Surface To Deteriorate |Repair To White And Colour Washed Surfaces  |Repair To Distemper Surface |How To Repair of Floor Damaged Surface  |Repair To Concrete And Terrazzo Floor |How to Repair To Damaged Plaster Surface |How To Repair To Timber Floors  |Surface worn out |Rot out the surface |How To Repair The Plaster And Floor Damaged surface

How to Repair To Damaged Plaster Surface

Some defects occur in the plaster surface after continuous use. This is mainly due to climate change and various chemical compounds in the air.

Related Post

Calculate The Estimate of Wall Plaster

How To Calculate The Block Quantity In Wall

These defects are of the following types

1. L.Cracks on the surface of the plaster.

2. The plaster peeling off

3. Plaster surface deterioration.

Cracks in the plaster surface

Cracks in the plaster surface can be very thin and large. In the case of fine cracks, cement is mixed with water to make a slurry and is grouted. In case of large cracks, the surface is roughened by removing the plaster around the cracks, then cement and sand mortar is prepared and plastered.

The plaster peeling off

Before plastering, a cement slurry is prepared and applied over the surface. It is then plastered and mixed with the old plaster. The reason for the plaster peeling off the surface is usually the presence of unnecessary moisture. Moisture should be noticed if the source is blocked before repairing. The plaster is then thoroughly cleaned by turning a steel brush around it. Later, the surface is re-plastered with cement mortar, which is leveled with the old plaster. But before plastering, cement slurry is prepared and applied over the such damaged surface.

Plaster Surface To Deteriorate

Unnecessary moisture and chemical compounds cause the plaster surface to deteriorate. To repair the damaged surface, the damaged plaster is first removed, then a cement slurry is applied over the surface and the surface is re-plastered and leveled with the old plaster.

Repair To White And Colour Washed Surfaces 

The building is whitewashed or color washed every year, the damaged surfaces should be repaired before whitewashing. It usually swelled out in different places. Such parts should be thoroughly cleaned with sandpaper. In addition, if there are any stains on the surface, they are also cleaned with a rag. The surfaces to be cleaned with a rag are covered with three coats and only one coat is applied on the remaining surfaces. Is. While applying the last coat, the brush should be run horizontally. While applying the first coat, the brush should be run vertically.

Repair To Distemper Surface

The distempered surface is re-distempered every year. Before re-distempering, all surface defects should be removed. Stains on the surface should be cleaned with the help of sandpaper. If the distempered surface is raised due to moisture etc., then the surface should be cleaned with the help of sandpaper and moisture should be removed. This is followed by two coats of distemper on the repaired surfaces and one coat on the normal second surface. For this purpose, the first coat is applied only on the repaired surfaces by running the brush in a vertical position. Then a coat of distemper is applied by running the brush horizontally on all the surfaces.

How To Repair of Floor Damaged Surface 

After continuous use, some defects occur in the floor, which need to be corrected. Because if not repaired, the defects increase. Depending on the type of floor, the floor is repaired as follows.

Repair To Concrete And Terrazzo Floor 

Floor Panel Repair

In case of damage to the upper surface of the concrete or chips floor, the damaged part is dug up to the base of the floor. If a floor panel settles, the entire panel is uprooted and the surface is thoroughly cleaned with a steel wire brush. After that curing is done with water for one day. Cement slurry is prepared and placed on the repairable part of the floor. The floor is then prepared according to the other material by placing a new material on top of the damaged part and leveling it with the rest of the floor. The top layer of the floor is cured for three days and ground after the topping. And finally polished.

Polishing the surface

After use for a long time, the upper surface of the chips and mosaic floor fades and the beauty of this floor is significantly reduced. It is re-polished to make it better. Before polishing floor is washed with oxalic acid or soap to remove all stains. The floor s then dried and well-polished. The way the floor becomes new. Removing stains and scars. While using the floor, different types of risks, etc. appear on the floor. Such as paint or ink marks or ghee and oil risks etc. To remove these marks, the floor surface is washed using Oxalic Acid or Washing Powder in warm water. Do not use washing soda or any other acid for this purpose as they damage the floor surface

How To Repair To Timber Floors 

The top of wooden floors deteriorates after continuous use. There are two opes of this disorder.

1. 1-Surface worn out

2. 2- Rot out the structure

1- Surface worn out

After using the wooden floor for a long time the surface of the wooden floor worn out. The worn part is carefully inspected and it is decided whether the wom part should be replaced or the old part should be repaired. If the part has 1/4 of its original thickness worn, the part is cut out and a new piece of wood is fitted according to the original measurement. In case of worn less than 1/4 part, the surrounding surface is leveled using plane or sandpaper and rasp. Finally, the entire surface is polished.

2- Rot out the surface

In the presence of moisture, the wood surface begins to rot out. The source of moisture is detected and repaired before the floor is repaired. If the wood surface is strong, plastic and bitumen are applied under the old wood. If the wood has deteriorated further, a new piece of wood is placed on top with plastic paper (“Polythene Paper”).

LEARN MORE

• Introduction And Types of Maintenance of Building With Full Details

• Purpose of Providing The Chair Bar And Calculate The Cutting length

• Seismic Proof Construction And Technical Terms 

• Important Principles For Design The Column

THANKS